Search
Latest topics
528 dies when warmed up CURED ! follow up.
2 posters
Page 1 of 1
528 dies when warmed up CURED ! follow up.
Resisting the temptation to buy a new camshaft position sensor which most people including myself, seemed to think was the source of the problem, I bought a PA SOFT Scanner interface first, to read any error codes myself. After duly setting up my PC in the shed near the car and plugging it in I ran a scan. Result 1 error in DME: "83". After a long time googling and reading threads on forums about other owners problems, I was able to establish this was a faulty Crankshaft position Sensor. £27+£2.95 postage from Tops Solutions on Ebay and after just over 24 hours the car is running perfectly again. The old genuine BMW sensor was noticably deteriorated around the joint where the cable entered the unit with the plastic actually crumbling and falling apart. I was lucky that my engine had the sensor fitted at the front beneath the thermostat housing, and not at the rear under the starter motor.
The PA Soft scanner worked well for the minimal cost but gives no clue to what the codes mean. I am now going in search by google etc,of the meaning of error code "6" in the SRS airbag module and hopefully get the airbag light off my dash. Is there a list somewhere out there of these error codes and there meaning?
Anyway hope my experiences are of help to somebody.
The PA Soft scanner worked well for the minimal cost but gives no clue to what the codes mean. I am now going in search by google etc,of the meaning of error code "6" in the SRS airbag module and hopefully get the airbag light off my dash. Is there a list somewhere out there of these error codes and there meaning?
Anyway hope my experiences are of help to somebody.
davemcc- Posts : 3
Join date : 2009-06-27
SRS error 6
Hallo,
follow this link for your error:
[url=bmw.bonesi.ch/pasoft]bmw.bonesi.ch/pasoft[/url]
hope it helps
damon
follow this link for your error:
[url=bmw.bonesi.ch/pasoft]bmw.bonesi.ch/pasoft[/url]
hope it helps
damon
damonbonesi- Posts : 1
Join date : 2009-07-24
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum
|
|
Tue Oct 21, 2014 1:35 am by carebmw
» sharing IKEYCUTTER CONDOR XC-007 Master Series Key Cutting Machine
Fri Jul 11, 2014 9:52 pm by vvdibmw
» Tuirel S777 Retail DIY Professional Hand-held Auto Scanner With Full Softwares
Tue Jun 03, 2014 2:55 am by vvdibmw
» What you should know about brake maintenance?
Thu May 08, 2014 3:15 am by vvdibmw
» e36 coupe front windows "bouncing"
Tue Mar 11, 2014 7:52 pm by hogpie
» FS: BMW Automatic Transmission - ZF 5HP24 - 2000 BMW X5 E53 4.4i - $1750 OBO
Mon Mar 03, 2014 8:37 pm by vvdibmw
» Lastest, Comprehensive BMW Multi tool V3.5 BMW Multi-Tool latest software V3.5 Powerful than AK300! [IMG]http://www.uobd2.com/upload/review/bmw-multi-tool-software_2012041583176601.jpg[/IMG] support there type of protocol:KWP-CAN BUS 100Kbps, KWP-CAN BU
Mon Mar 03, 2014 8:32 pm by vvdibmw
» How to make BMW Auto Key Programmer
Thu Feb 27, 2014 1:37 am by vvdibmw
» Bootlid gas struts
Tue Dec 31, 2013 1:01 am by vvdibmw